Other compatible accessories

A variety of accessories are available for your Nikon camera.

Compatible accessories

  • Availability may vary with country or region.
  • See our website or brochures for the latest information.

Power sources

  • EN-EL25a/EN-EL25 Rechargeable Li-ion Battery: Can be used with Nikon Z 30 digital cameras.
    • The number of shots that can be taken (battery life) differs (Battery endurance) because the battery capacity differs when using the EN-EL25a and the EN-EL25.
  • MH-32 Battery Charger: Can be used to recharge EN-EL25a/EN-EL25 batteries.
  • EH-8P AC Adapter: The EH-8P can be used to charge batteries inserted in the camera.
    • The optional UC-E25 USB cable (featuring Type C connectors at both ends) is required to supply power to the camera or charge the battery using the EH-8P. The supplied USB cable cannot be used.
    • The battery will not charge while the camera is on.
    • The AC adapter can be used to power the camera; to do so, select [Enable] for [USB power delivery] in the setup menu. For more information, see “USB power delivery” (USB power delivery).
  • EH-7P Charging AC Adapter: The EH-7P can be used to charge batteries inserted in the camera.
    • The battery will not charge while the camera is on.
    • The charging AC adapter can be used to power the camera; to do so, select [Enable] for [USB power delivery] in the setup menu. For more information, see “USB power delivery” (USB power delivery).

USB cables

  • UC-E24 USB Cable: This cable is the same as the USB cable supplied with the camera. A USB cable with a type C connector for connection to the camera and a type A connector for connection to the USB device.
  • UC-E25 USB Cable: A USB cable with two type C connectors. The UC-E25 USB cable is required to connect this camera to the EH-8P AC adapter.

Filters

  • Neutral Color (NC) filters can be used to protect the lens.
  • Filters may cause ghosting when the subject is framed against a bright light, or when a bright light source is in the frame. Filters can be removed if ghosting occurs.
  • Matrix metering may not produce the desired results with filters with exposure factors (filter factors) over 1× (Y44, Y48, Y52, O56, R60, X0, X1, C-PL, ND2S, ND4, ND4S, ND8, ND8S, ND400, A2, A12, B2, B8, B12). We suggest that [Center-weighted metering] be selected instead. See the filter documentation for details.
  • Filters intended for special-effects photography may interfere with autofocus or the in-focus indicator (I).

Hot shoe adapters

AS-15 Sync Terminal Adapter: Mount the AS-15 on the camera hot shoe to connect studio strobe lights or other flash equipment via a sync terminal.

Accessory shoe covers

BS-1 Accessory Shoe Cover: A cover protecting the accessory shoe when no flash unit is attached.

Body caps

BF-N1 Body Cap: The body cap prevents dust entering the camera when no lens is in place.

Mount adapters

FTZ II/FTZ Mount Adapter: An adapter that allows NIKKOR F mount lenses to be used with digital cameras that support interchangeable Z mount lenses.

  • For information on attaching, removing, maintaining, and using mount adapters, refer to the documentation supplied with the device.
  1. If a warning message prompting you to update is displayed on the camera when a mount adapter is mounted on the camera, update to the latest version. For information on firmware updates, see the Nikon website for your area.

Microphones

  • ME-1 Stereo Microphone: Connect the ME-1 to the camera microphone jack to record stereo sound. Using an external microphone also reduces the chance of picking up equipment noise, such as the sounds produced during video recording when focus is achieved using autofocus.
  • ME-W1 Wireless Microphone: A wireless Bluetooth microphone. Use the ME-W1 for off-camera recording.

Remote controls

ML-L7 Remote Control: Pair it with the camera and shoot videos and photos remotely.

Attaching and removing the accessory shoe cover

The optional BS-1 Accessory Shoe Cover slides into the shoe as shown. To remove the cover, hold the camera firmly, press the cover down with a thumb and slide it in the direction shown.

ML-L7 Remote Control

You can operate the camera from the remote control by pairing* (Connecting for the first time: Pairing) the optional ML-L7 Remote Control with the camera. With this camera, you can perform the operation in “Parts and functions of the remote control (for Z 30)” (Parts and functions of the remote control (for Z 30)).

  1. Connecting the camera and remote control via Bluetooth is called “pairing” here.
  • Only one remote control can be paired per camera. When pairing another remote control, only the last paired remote control is enabled.
  • Also see the documentation supplied with the ML-L7 Remote Control.

Notes when using the remote control

  • The remote control cannot be used in the following cases.
    • When [Airplane mode] in the camera setup menu is set to [Enable]
    • While the camera is connected to and exchanging data with another device via USB
  • A connection between the camera and the remote control and a connection (Bluetooth or Wi-Fi) between the camera and another device cannot be established at the same time.

Parts and functions of the remote control (for Z 30)

PartFunction
1- buttonSame operation as the W (Q) button on the camera.
2+ buttonSame operation as the X button on the camera.
3Video-record buttonPress to start recording, and press again to end recording.
4Power buttonWhen pressed, the remote control turns on and starts searching for a paired camera. If you press and hold it for 3 seconds or longer, the remote control will start searching for unpaired cameras. Pressing the power button while the remote control is on will turn it off.
5Status lampThe remote control status and shooting operation status are indicated by the color and behavior of the lamp (Remote control status lamp (for Z 30)).

PartFunction
6Shutter-release button

Press the button to release the shutter.

  • When using autofocus, the shutter is released after focusing with autofocus.
  • The remote control shutter-release button cannot be pressed halfway.
  • The remote control shutter-release button cannot be kept pressed for burst photography.
  • The procedure for taking photographs at a shutter speed of “Bulb” is the same as that for “Time”.
7Multi selectorSame operation as the multi selector on the camera.

PartFunction
8J (select) buttonSame operation as the J button on the camera.
9Fn1 (function 1)/Fn2 (function 2) button

Use functions registered beforehand (Assign Fn1 button/Assign Fn2 button).

  • By default, pressing the Fn1 button on the remote control is the same operation as the K button on the camera, while the Fn2 button is the same operation as the G button.

Adjusting focus from the camera

If [Focus] is selected for Custom Setting a2 [AF-S priority selection] in focus mode AF-S, focus will lock when the camera shutter-release button is pressed halfway. You can then press the shutter-release button on the remote control to take a picture at the selected focus position.

Standby timer when using the remote control

When the standby timer of the camera expires and the monitor is off, turn on the remote control and then press and hold the shutter-release button or video-record button on the remote control to return to the original state.

Remote control status lamp (for Z 30)

ColorStatusDescription
GreenFlashing about every secondDetecting paired camera
GreenFlashing quickly (about every 0.5 seconds)Pairing
GreenFlashing about every 3 secondsConnected to the camera
OrangeFlashes onceStart shooting photo
OrangeFlashes twiceEnd shooting photo
RedFlashes onceStart recording video
RedFlashes twiceEnd recording video

Connecting for the first time: Pairing

When using the remote control for the first time, you must pair it with the camera.

  1. Select [Wireless remote (ML-L7) options] > [Save wireless remote controller] in the camera setup menu and press J.
    • The camera will standby for pairing.
    • If the camera is connected to a smartphone or computer, connection to those devices will be terminated.
  2. Press and hold the power button on the remote control (3 seconds or longer).
    • The camera and remote control will start pairing. In the meantime, the remote control status lamp flashes at about 0.5 second intervals.
    • When pairing is complete, the camera and remote control will be connected. L and Z are displayed in the shooting display.
    • If a message indicating that pairing failed is displayed, start over from Step 1.

To connect with a paired remote control

  1. Select [Wireless remote (ML-L7) options] > [Wireless remote connection] > [Enable] in the camera setup menu and press J.
  2. Press the power button on the remote control.
    • The camera and remote control are automatically connected.