To use radio AWL with compatible flash units, attach a WR-R10 wireless remote controller to the camera and establish a wireless connection between the flash units and the WR-R10.

Establishing a Wireless Connection

Before using radio AWL, establish a wireless connection between the WR-R10 and the remote flash units.

  1. C: Connect the WR-R10.

    Connect the WR-R10 to the camera. For more information, see the documentation provided with the WR-R10.

  2. C: Select Radio AWL for Flash control > Wireless flash options in the photo shooting menu.

  3. C: Choose a channel.

    Set the WR-R10 channel selector to the desired channel.

  4. C: Choose a link mode.

    Select Wireless remote (WR) options > Link mode in the setup menu (0 Wireless Remote (WR) Options) and choose from the following options:

    • Pairing: The camera connects only to devices with which it has previously been paired, preventing signal interference from other devices in the vicinity. Given that each device must be paired separately, PIN is recommended when connecting to a large number of devices.
    • PIN: Communication is shared among all devices with the same four-digit PIN, making this a good choice for photography featuring a large number of remote devices. If there are multiple cameras present that share the same PIN, the flash units will be under the sole control of the camera that connects first, preventing all other cameras from connecting (the LEDs on the WR-R10 units connected to the affected cameras will blink).

  5. f: Establish a wireless connection.

    Set the remote flash units to radio AWL remote mode and set the devices to the channel you selected in Step 3, then pair each of the remote units with the WR-R10 according to the option selected in Step 4:

    • Pairing: Initiate pairing on the remote unit and press the WR-R10 pairing button. Pairing is complete when the LINK lamps on the WR-R10 and flash unit flash orange and green; once a connection is established, the LINK lamp on the remote flash unit will light green.
    • PIN: Use the controls on the remote flash unit to enter the PIN you selected in Step 4. The LINK lamp on the remote unit will light green once a connection is established.
  6. f: Confirm that the flash-ready lights for all flash units are lit.

    In radio AWL, the flash-ready indicator will light in the camera viewfinder or flash information display when all flash units are ready.

The WR-R10 Wireless Remote Controller

A WR-A10 adapter is required when using the WR-R10. Be sure to update the WR-R10 firmware to version 3.0 or later; for information on firmware updates, see the Nikon website for your area.

Listing Remote Flash Units

To view the flash units currently controlled using radio AWL, select Flash control > Radio remote flash info in the photo shooting menu. The identifier (“remote flash name”) for each unit can be changed using flash unit controls.

Connected flash unit

Group Flash-ready indicator

Reconnecting

As long as the channel, link mode, and other settings remain the same, the WR-R10 will automatically connect to previously paired flash units when you select remote mode and Steps 3–5 can be omitted. The flash unit LINK lamp lights green when a connection is established.

Adjusting Flash Settings

After selecting Radio AWL for Flash control > Wireless flash options in the photo shooting menu, select Group flash, Quick wireless control, or Remote repeating for Remote flash control and adjust settings as described below.

Group Flash

Select this option to adjust settings separately for each group.

  1. C: Select Group flash for Flash control > Remote flash control in the photo shooting menu.

  2. C: Select Group flash options.

    Highlight Group flash options in the flash control display and press 2.

  3. C: Choose the flash control mode.

    Choose the flash control mode and flash level for the master flash and the flash units in each group:

    • TTL: i-TTL flash control.
    • qA: Auto aperture (available only with compatible flash units).
    • M: Choose the flash level manually.
    • – – (off): The units do not fire and the flash level cannot be adjusted.

  4. f: Group the remote flash units.

    Choose a group (A–F) for each of the remote flash units. The master flash can control up to 18 flash units in any combination.

  5. C/f: Compose the shot.

    Compose the shot and arrange the flash units. See the documentation provided with the flash units for more information. After arranging the units, press the i button in the flash info display (0 Changing Flash Settings) and select M Test flash to test fire the units and confirm that they are functioning normally.

  6. C: Frame the photograph, focus, and shoot.

Quick Wireless Control

Select this option to control overall flash compensation for, and the relative balance between, groups A and B, while setting output for group C manually.

  1. C: Select Quick wireless control for Flash control > Remote flash control in the photo shooting menu.

  2. C: Select Quick wireless control options.

    Highlight Quick wireless control options in the flash control display and press 2.

  3. C: Adjust flash settings.

    Choose the balance between groups A and B.

    Adjust flash compensation for groups A and B.

    Choose a flash control mode and flash level for the units in group C:

    • M: Choose the flash level manually.
    • – –: The units in group C do not fire.

  4. f: Group the remote flash units.

    Choose a group (A, B, or C). The master flash can control up to 18 flash units in any combination.

  5. C/f: Compose the shot.

    Compose the shot and arrange the flash units. See the documentation provided with the flash units for more information. After arranging the units, press the i button in the flash info display (0 Changing Flash Settings) and select M Test flash to test fire the units and confirm that they are functioning normally.

  6. C: Frame the photograph, focus, and shoot.

Remote Repeating

When this option is selected, the flash units fire repeatedly while the shutter is open, producing a multiple-exposure effect.

  1. C: Select Remote repeating for Flash control > Remote flash control in the photo shooting menu.

  2. C: Select Remote repeating options.

    Highlight Remote repeating options in the flash control display menu and press 2.

  3. C: Adjust flash settings.

    Choose the flash level (Output), the maximum number of times the flash units fire (Times), and the number of times the flash units fire per second (Frequency).

    Enable or disable selected groups. Select ON to enable the selected group, – – to disable the selected group.

  4. f: Group the remote flash units.

    Choose a group (A–F) for each of the remote flash units. The master flash can control up to 18 flash units in any combination.

  5. C/f: Compose the shot.

    Compose the shot and arrange the flash units. See the documentation provided with the flash units for more information. After arranging the units, press the i button in the flash info display (0 Changing Flash Settings) and select M Test flash to test fire the units and confirm that they are functioning normally.

  6. C: Frame the photograph, focus, and shoot.

Adding a Shoe-Mounted Flash Unit

Radio-controlled flash units can be combined with any of the following flash units mounted on the camera accessory shoe:

  • SB-5000: Before attaching the flash unit, set it to radio-controlled master flash mode (a d icon will appear at the top left corner of the display) and choose group or remote repeating flash control. Once the unit is attached, settings can be adjusted using the controls on the flash unit or the options listed in the camera menus under Group flash options > Master flash or under “M” in the Remote repeating options display.
  • SB-910, SB-900, SB-800, SB-700, SB-600: Configure the flash for stand-alone use and use the controls on the flash unit to adjust flash settings.
  • SB-500, SB-400, SB-300: Mount the unit on the camera and adjust settings using the camera Group flash options > Master flash option.